Commercial

Won't interfere with passenger leg space Can be used with factory installed console One Offset Universal Mounting Step ( DS-STEP ) is already included with this vehicle base. However, additional Offset Universal Mounting Steps can be ordered to stack on top of each other if needed For extra stability, a Support Brace ( 7160-0230 ) is recommended Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance Note: Forward seat travel is affected

Bracket mounted to pole gusset allows for additional attachment to seat frame Base works with most existing work boxes Attaches to the passenger side inner front and back seat studs Does not interfere with the passenger leg space Does not require drilling Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Will not interfere with levers or factory installed console Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance A Support Brace ( 7160-0230 ) is highly recommended

Angled step moves pole away from passenger leg space and attaches to the Lower Pole without any protruding edges One Offset Universal Mounting Step ( DS-STEP ) is already included with this vehicle base. However, additional Off set Universal Mounting Steps can be ordered to stack on top of each other if needed. Multiple mounting slots allow for flexible positioning of the Offset Universal Mounting Step Larger base footprint and reinforced flanges provide added stability Heavy gauge steel construction for long-term durability Black powder coat finish for maximum corrosion resistance

The entire arm can rotate around 360° with locking points at every 15° To rotate the arm simply pull the front lever out, rotate to desired position and then release the lever Locking slide arm can telescope 9” to 13” from the center of the pole and utilizes the industry first, Slam and Lock technology, that allows you to simply push the computer back to the retracted position and it automatically locks into place Compatible Motion Attachment hole patterns: VESA 75mm Gamber-Johnson 2x4 NEC AMPS Tilt capabilities: 90° forward allows for tablets to be easily mounted 26° aft movement Riveted design allows for smoother tilt movement Swivel capabilities: 360° Heavy duty, spring loaded steel, side pin was tested to 50,000+ cycles Can be mounted directly to a flat surface or on any Upper Pole, Complete Pole, Center Pole, Low Profile Bracket or Gamber-Johnson 3-hole pattern Two PEMs added to the back of the Mongoose to attach the Tablet Display Mount ( 7160-0494 or 7160-0529 ) Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Attaches to the seat studs on the passenger side floor, under the seat Install in minutes with no drilling required Will not interfere with levers or factory installed consoles An Offset Universal Mounting Step ( DS-STEP ) maybe ordered separately to move the pole away from passenger leg space

Won’t interfere with passenger leg space Bracket mounted to pole gusset allows for additional attachment to seat frame Base works with most existing work boxes Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Conveniently holds printer and paper in separate trays New wire draw latch provides a secure fit to reduce vibration noise Bolt-on cable restraint provided a cable management options if desired Paper roll cut-out allows for vertical orientation as well as standard horizontal orientation Printer can be easily removed from the mount for use outside of the vehicle Constructed of heavy gauge steel and powder coated for long term durability

Vehicle Base will work with both the Stow & Go and Swivel & Go Dodge Caravan models Won’t interfere with passenger leg space Installs in minutes using passenger side inner front and back seat studs with no drilling required Heavy gauge steel construction for long-term durability Black powder coat finish for maximum corrosion resistance For extra stability a Support Brace ( 7160-0230 ) is recommended Note: On Stow & Go Dodge Caravan models, the front seat will have limited travel due to the install of the base and this may cause the rear passenger seat not to stow properly.

Rugged construction for long-term durability Flexible design On/off switch allows you two (2) different LED color combinations: Red White

Won’t interfere with passenger leg space Heavy gauge steel construction for long-term durability Black powder coat finish for maximum corrosion resistance For extra stability a Support Brace ( 7160-0230 ) is recommended

Base uses weight and pressure of the seat and the mechanical counter balance of the base design to secure it under the seat. We recommend fastening the base using the four (4) holes located on the base and drilling into the vehicle floor for extra security rather than using the seat bolts. One (1) Offset Universal Mounting Step ( DS-STEP ) included with vehicle base. Additional Offset Universal Mounting Steps can be ordered to stack on top of each other if needed. Offset Universal Mounting Step should be pointed towards the passenger seat to move the mounting system away from the dash. Support Brace ( 7160-0230 ) is highly recommended to reduce system vibration Heavy gauge steel construction for long-term durability Black powder coat finish for maximum corrosion resistance

Angled step moves pole away from passenger leg space Will not interfere with levers or factory installed consoles One Off-set Universal Mounting Step ( DS-STEP ) is already included with this vehicle base. However, additional Off-set Universal Mounting Steps can be ordered to stack on top of each other if needed. Heavy gauge steel construction for long-term durability Black powder coat finish for maximum corrosion resistance A support brace ( 7160-0230 ) is highly recommended. An existing bolt (heater box mounting bolt) in the vehicle can be used as an attachment point for the support brace.

Black powder coat finish for maximum corrosion resistance Won’t interfere with levers or factory-installed consoles located on transmission hump Won’t interfere with passenger leg space For extra stability a Support Brace ( 7160-0230 ) is recommended

Base is secured between passenger seat base and seat bolts Installs in minutes with no drilling required Support Brace is recommended ( 7160-0231 ) which utilizes the factory hole in the base of seat (no drilling required) To complete the mounting system, see our full line of Lower and Upper Poles, Motion Attachments and Computer Mounts Heavy gauge steel construction for long-term durability Black powdercoat finish for maximum corrosion resistance

Base designed to work with both the police and street model Dodge Charger and Magnum Attaches to passenger side floor, under seat Can be used with factory installed console A Support Brace ( 7160-0230 ) is highly recommended

Clips convert the Gamber-Johnson NotePad™ V ( 7160-0250 ) and NotePad™ V-LT ( 7160-0402 ) so that they can be used with smaller notebook, convertible tablet and tablet formats Reduces the rear profile of the cradle when used with tables The kit provides an overall depth adjustment of 7.2” (18.3 cm) - 9” (22.9 cm) Accommodates tablets in cases